Aoc I2260PWHU Manual de usuario

LED Backlight I2260PWHU

10 Setup Stand & Base Please setup or remove the base following the steps as below. Setup: Remove:

11 Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to you

12 Connecting the Monitor Cable Connections In Back of Monitor and Computer: 1. USB 2. Power 3 HDMI 4 .DVI 5. Analog (DB-15 VGA cable)

13 Wall Mounting Preparing to Install An Optional Wall Mounting Arm. This monitor can be attached to a wall mounting arm you purchase separatel

Adjusting Setting Optimal Resolution Windows 8 For Windows 8: 1. Right click and click All apps at the bottom-right of the screen.2. Set the “View by”

4. Click DISPLAY.5. SettheresolutionSLIDE-BARtoOptimalpresetresolution15

Windows 7 For Windows 7: 1.1.Click START.2.2.Click CONTROL PANEL.3.3.Click APPEARANCE.4.4.Click DISPLAY.16

5. Set the resolution SLIDE-BAR to Optimal preset resolution.17

18 Windows Vista For Windows Vista: 1 Click START. 2 Click CONTROL PANEL. 3 Click Appearance and Personalization. 4 Click Personalization

19 5 Click Display Settings. 6 Set the resolution SLIDE-BAR to Optimal preset resolution

2 Safety ...

20 Windows XP For Windows XP: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance and Themes. 5 Double click DISPL

21 6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to Optimal preset resolution Windows ME/2000 For Windows ME/2000: 1 Click START. 2 Click SE

22 Hotkeys 1 Source/Auto/Exit 2 ECO(DCR)/< 3 Volume / > 4 Menu/Enter 5 Power Power Press the Power button to turn on/off the monitor.

23 OSD Setting Basic and simple instruction on the control keys. 1) Press the MENU-button to activate the OSD window. 2) Press < or >

24 Luminance 1

25 4

26 DCR Off Disable dynamic contrast ratio On Enable dynamic contrast ratio Overdrive Weak Medium Strong Off

27 Image Setup 1 Press to display menu. 2 Press < or > to select (Image Setup), and press to enter. 3 Press < or > to

28 Press < or > to adjust. 5 Press to exit. Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise. Phase 0-100

29 Color Setup 1 Press (Men

3 EPA Energy Star ...

30 4 Press < or > to adjust. 5 Press to exit. Color setup. Warm Recall Warm Color Temperature from EEPROM. Normal Recall No

31 Picture Boost 1 Press (Menu) to display menu. 2 Press < or > to select (Picture Boost), and press to enter. 3 Press &l

32 4 Press < or > to adjust. 5 Press to exit. Frame Size 14-100 Adjust Frame Size Brightness 0-100 Adjust Frame Brightn

33 OSD Setup 1 Press (Menu) to display menu. 2 Press < or > to select (OSD Setup), and press to enter. 3 Press < or &g

34 4 Press < or > to adjust. 5 Press to exit. H.Position 0-100 Adjust the horizontal position of OSD V.Position 0-100

35 Extra 1 Press (Menu) to display menu. 2 Press < or >to select (Extra), and press to enter. 3 Press < or > to sel

36 4 Press < or > to adjust. 5 Press to exit. Input Select Auto Config yes or no Auto adjust the picture to default Of

37 Exit 1 Press (Menu) to display menu. 2 Press < or > to select (Exit), and press to enter. 3 Press to exit

38 Exit Exit the main OSD LED Indicator Status LED Color Full Power Mode Green Active-off Mode Orange

Driver Monitor Driver Windows 8 1. Start Windows® 82. Right click and click All apps at the bottom-right of the screen.3. Click on the “Control panel”

4 Safety National Conventions The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throug

5. Click on the “Display” icon.6. Click on the “Change display settings” button.7. Click the “Advanced Settings” button.8. Click the “Monitor” tab and

9. Click the “Driver” tab.10. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver... “ andthen click the "

12. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory:X:\Driver\module name (where X is the drive let

43 Windows 7 1.Start Windows® 7 2.Click on the 'Start' button and then click on 'Control Panel'. 3. Click on the 'Displa

44 4.Ckick on the “Change display settings” button. 5.Click the “Advanced Settings” button. 6.Click the “Monitor” tab and then click the “Pro

45 7.Click the “Driver” tab. 8. Open the "Update Driver Software-Generic PnP Monitor" window by clicking on “Update Driver... “and then

46 10. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:\Driver\module name (where X is the

47 Windows Vista 1. Click "Start " and "Control Panel". Then, double-click on "Appearance and Personalization".

48 4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration fo

4 9Windows XP 1. Start Windows® XP 2. Click on the 'Start' button and then click on 'Control Panel'. 3. Select and click o

5 Power The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied t

50 5. Select the 'Settings' tab then click on the 'Advanced' button. 6. Select 'Monitor' tab - If the 'Propert

51 8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button. 9. S

52 Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Pa

53 i-Menu Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the O

54 e-Saver Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allow

55 Screen+ Welcome to "Screen+" software by AOC, Screen+ software is a desktop screen splitting tool, it splits the desktop into diff

56 Troubleshoot Problem & Question Possible Solutions Power LED Is Not ON Make sure the power button is ON and the Power Cord is properly co

57 Monitor Is Stuck In Active Off-Mode" The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly

58 Specification General Specification Panel Model name I2260PWHU Driving system TFT Color LCD Viewable Image Size 54.62 cm diagonal Pixel p

59Preset Display Modes STANDARD RESOLUTION HORIZONTAL FREQUENCY(kHZ) VERTICAL FREQUENCY(Hz) VGA 640x480@60Hz 31.469 59.94 VGA 640x480@72Hz

6 Installation Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause

60 Pin Assignments Pin Number 15-Pin Side of the Signal Cable 1 Video-Red 2 Video-Green 3 Video-Blue s N.C. 5 Detect Cable 6 GND-R 7 GND-G 8 GND-B

61 Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 TMDS Data 2+ 9 TMDS Data 0 17 DDC/CEC Ground 2 TMDS Data 2 Shield 10 TMDS Cloc

62 Regulation FCC Notice FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been teste

63WEEE Declaration Disposal of Waste Equipment by Users in Private Household in the European Union. This symbol on the product or on its packagi

WEEE/E-Waste declaration for India This symbol on the product or on its packaging indicates that this product must not be disposed of with your oth

65EPEAT Declaration EPEAT is a system to help purchasers in the public and private sectors evaluate, compare and select desktop computers, notebooks

66 Service EU WARRANTY FOR AOC MONITORS LIMITED THREE-YEAR WARRANTY* For AOC LCD Monitors sold within Europe, AOC International (Europe) B.V. warrant

67PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER

68Warranty Statement for North & South America (excluding Brazil) WARRANTY STATEMENT for AOC Color Monitors Including those Sold within N

69MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR AND ONE (1) YEAR F

7 Cleaning Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauter

70 TCO DOCUMENT

8 Other If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center. Make sur

9 Setup Contents in Box Not all signal cables (VGA, DVI,USB and HDMI cables) will be provided for all countries and regions. Please check with the